EUROLUB Oil Adviser

EUROLUB Oil-Advisor

Confused! which Oil is suitable for your car? Don't be just visit EuroLub Oil-Finder and choose your car type to make sure you order the right item.

Viscosity / HTHS rate viscosity

Viscosity describes the internal friction of fluids and indicates their flow characteristics at low and high temperatures.

High Temperature High Shear (HTHS) rate viscosity – indicates dynamic viscosity and is measured in millipascal seconds (mPa*s) at 150 °C and under extremely high shear loads of up to 106 s-1. It describes the characteristics of lubricants under certain operating conditions at the cylinder wall or inside the connecting rod or crankshaft bearing.

Low HTHS: 2.9 – 3.5 mPas = low HTHS viscosity, allows for low fuel consumption. High HTHS: > 3.5 mPas = high HTHS viscosity, high degree of wear protection.

SAE viscosity grades

The viscosity grades of engine oils are defined by the SAE J300 (Society oft Automotive Engineers), for instance SAE 10W40: The number preceding the letter W indicates the viscosity at low temperatures; the smaller the value in front of the W, the lower the viscosity of the oil at low temperatures. (the “W” stands for winter). The number following the W represents the viscosity at high temperatures; the higher the warm viscosity, the higher the loads the oil can handle at high temperatures. To avoid any confusion between engine and transmission oils, the viscosity grades applying to transmission oils are defined following SAE J306 (e.g. SAE 75W90).

Temperature ranges for motor oils 

einsatzbereiche

SAPS-Level

The SAPS level defines the portion of sulfate ash, phosphorus, and sulfur in engine oils.

Low SAPS – strictly limited portion of sulfate ash (< 0.5 %), phosphorus (0.05 %), and sulfur (< 0.2 %). Mid SAPS – limited portion of sulfate ash (< 0.8 %), phosphorus (0.07 – 0.09 %), and sulfur (< 0.3 %). Full SAPS – no limitations to the portion of sulfate ash, phosphorus, and sulfur.

API classifications

The classifications of the API (American Petroleum Institute) describe the quality requirements to be met by engine and transmission oil in the United States.

ACEA sequences

As the operating conditions and engine characteristics fundamentally differ between Europe and the United States, the ACEA (Association des Constructeurs Européens d’Automobiles) introduced its own classification system in 1996. While based on the API classifications, the ACEA sequences focus to a greater extent on the specific lubricant requirements that apply to engines built into European automobiles as well as the respective EURO emission standards. Meeting these requirements also involves the successful completion of test runs for lubricants used in European test engines. The current ACES sequences are grouped into A sequences (A1, A3, and A5) for passenger car gas engines, B sequences (B1, B3, B4, and B5) for engine oils used in diesel passenger cars, C sequences (C1, C2, C3, and C4) for engine oils with a limited SAPS level, and E sequences (E2, E4, E6, E7, and E9) for engine oils used in diesel trucks.

Fuel-economy engine oils

Fuel-economy engine oils are defined as oils that allow for a low consumption of fuel.

 

Our oils for EUROLUB gas engines meet these requirements

  • consist of carefully selected mineral base oils with the latest additives;
  • tested and approved by manufacturers, for example, MAN, Jenbacher, etc.;
  • always available in stock.

Engine Oils for Classic and Antique Cars (Classic Oils)

Antique cars are more than just auto mobiles. They are priceless to their owners and worth much more than their actual monetary value. This is why the chemistry has to be right – not only in the figurative sense of the word, but quite literally.

We have, therefore, added Classic Oil to our latest product line. The oils in this product family have been designed specifically to accommodate the operating characteristics typically found in older engine generations. The best oils for your four-wheeled beauties.

 

USD